- Mon - Sat : 9:00 - 17:00
- + 91-9924300407
- saffromellow@yahoo.com
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
| COLOUR | : Grey |
|---|---|
| FINISH | : Matt |
| SOLIDS BY VOLUME | : 40 ± 3% |
| THEORETICAL SPREADING RATE | : 13.33 sq.mt / lit at recommended DFT of 30 µ |
| FLASH POINT | : Base : Above 23° C Hardener : Above 30° C |
| DRYING CHARACTERISTICS (At 30° C and 65% Relative humidity) | : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE | : BASE : 6months HARDENER : 6 months |
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
| MIXING RATIO | : Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION | : By Brush / By Conventional Spray |
| THINNER | : Thinner 290 |
| POT LIFE | : 3 hours min at 30° C |
| RECOMMENDED DFT | : 30-40 µ. |
| OVERCOATING INTERVAL | : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) |
| COMPATIBILITY | : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 10-15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | 10-15% |
| Addition : | Max 5% |
| Nozzle Orifice : | 0.28- 0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50°C). Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum, for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
| COLOUR :- | Yellow |
|---|---|
| FINISH :- | Matt |
| SOLIDS BY VOLUME :- | 40 ± 3% |
| THEORETICAL SPREADING RATE :- | 13.33 sq.mt / lit at recommended DFT of 30 µ |
| FLASH POINT :- | Base : Above 23° C Hardener : Above 30° C |
| DRYING CHARACTERISTICS (At 30° C and 65% Relative humidity) :- | SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE :- | BASE : 6months HARDENER : 6 months |
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
| MIXING RATIO :- | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION :- | By Brush / By Conventional Spray |
| THINNER :- | Type 290 |
| POT LIFE :- | 3 hours min at 30° C |
| RECOMMENDED DFT :- | 30-40 µ. |
| OVERCOATING INTERVAL :- | MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) |
| COMPATIBILITY :- | Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 10-15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5% |
| Nozzle Orifice : | 0.28- 0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50°C). Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum, for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
| COLOUR : | Red |
|---|---|
| FINISH : | Matt |
| SOLIDS BY VOLUME : | 40 ± 3% |
| THEORETICAL SPREADING RATE : | 13.33 sq.mt / lit at recommended DFT of 30 µ |
| FLASH POINT : | Base : Above 23° C Hardener : Above 30° C |
| DRYING CHARACTERISTICS (At 30° C and 65% Relative humidity) : | SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6months HARDENER : 6 months |
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
| MIXING RATIO : | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Conventional Spray |
| THINNER : | Type 290 |
| POT LIFE : | 3 hours min at 30° C |
| RECOMMENDED DFT : | 30-40 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) |
| COMPATIBILITY : | Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 10-15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5% |
| Nozzle Orifice: | 0.28- 0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50°C). Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum, for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
| COLOUR : | Red |
|---|---|
| FINISH : | Matt |
| SOLIDS BY VOLUME : | 40 ± 3% |
| THEORETICAL SPREADING RATE : | 13.33 sq.mt / lit at recommended DFT of 30 µ |
| FLASH POINT : | Base : Above 23° C Hardener : Above 30° C |
| DRYING CHARACTERISTICS (At 30° C and 65% Relative humidity) : | SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6months HARDENER : 6 months |
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
| MIXING RATIO : | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Conventional Spray |
| THINNER : | Type 290 |
| POT LIFE : | 3 hours min at 30° C |
| RECOMMENDED DFT : | 30-40 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) |
| COMPATIBILITY : | Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 10-15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5% |
| Nozzle Orifice : | 0.28- 0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50°C). Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum, for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component air-drying intermediate/primer surfacer coat.
Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.
| COLOUR : | Grey, White |
|---|---|
| FINISH : | Egg Shell to Matt |
| SOLIDS BY VOLUME : | 40 ± 3% |
| SPREADING RATE : | 13.3 sq.mt / ltr at recommended DFT of 30 µ |
| FLASH POINT : | Base : 23°C Hardener : 23°C |
| DRYING CHARACTERISTICS (At 30°C & 65% Relative Humidity) : | SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.
| MIXING RATIO : | Base: Hardener ( As per our recommendation) |
|---|---|
| APPLICATION : | By Brush/ By Conventional Spray / By Airless Spray |
| THINNER : | Type 290 |
| POT LIFE : | 4 hours min at 30° C |
| RECOMMENDED DFT : | 30 -35 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensure the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 5-15% |
| Nozzle Orifice : | 1.2-1.4mm |
| Nozzle Pressure : | 40-70 p.s.i |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28-0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component, air drying polyurethane based clear.
This product is recommended Top coat for glossy , uv protection,weather property and also as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system.
| COLOUR : | Clear |
|---|---|
| FINISH : | Smooth & Glossy |
| SOLIDS BY VOLUME : | 40 ± 3% |
| THEORETICAL SPREADING RATE : | 16 sq.mt / ltr at a DFT of 25 µ |
| FLASH POINT : | Base : Above 23°C Hardener : Above 23°C |
| DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30°C) : | HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
New concrete should be cured for at least 1 month prior to paint application. Ensure concrete surface is absolutely dry and free from moisture, oil, laitance, dust and dirt. For old concrete, ensure surface is free from oil, grease, algal & fungal growth and any old coating. Sand Blasting on concrete gives the best performance and should be given first preference out of the available surface preparation methods. If blasting is impracticable, Acid Etching with diluted Hydrochloric Acid followed by fresh water washing to be adopted. Seasoned wooden articles should be scuffed with Emery 220/400 to achieve smooth surface. Please refer our Directive Sheet on Surface Preparation.
| MIXING RATIO : | Base : Hardener (As per our recommendations) |
|---|---|
| APPLICATION : | By Brush / By Conventional Spray |
| THINNER : | Type 290 |
| POT LIFE : | 3 hours min at 30° C |
| RECOMMENDED DFT : | 30-40 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : Indefinite |
| COMPATIBILITY : | Can be applied on Epoxy primers and oleo-resinous primer and coated / over coated by two component paints like Epoxy, PU, etc. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :-By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Use quality brushes for paint application. Brushes made up of hog bristles are highly recommended. Size of the brush should be in proportion to the work in hand. Large size brushes (100-125 mm) for large areas and small brushes (25-50 mm) for narrow areas should be used.
| Thinner : | Type 290 |
|---|---|
| Addition : | 10-15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10° C or rises above 50° C, when Relative Humidity is above 85% & during rain, fog, or mist. Do not apply on hot surface (above 50° C). Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two component acrylic aromatic polyurethane finish coating
This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries.
It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry.
| COLOUR : | Assorted shades |
|---|---|
| FINISH : | Glossy / Semi glossy / Matt |
| SOLIDS BY VOLUME : | 40 ± 3% (Depends on shade) |
| THEORETICAL SPREADING RATE : | 13.33 sq.mt / lt at recommended DFT of 30 µ |
| FLASH POINT : | Base : Above 23° C Hardener : Above 23° C |
| DRYING CHARACTERISTICS (At 30° C and 65% Relative humidity) : | SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 DAYS. |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding.
| MIXING RATIO : | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Conventional spray / By Airless Spray |
| THINNER : | Type 290 |
| POT LIFE : | 3 hours min at 30° C |
| RECOMMENDED DFT : | 30-40 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 400 mesh size and apply uniformly over the surface. All equipments used for above should
Application :-By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner, to ensure the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 5-15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, do not apply during rain, fog & mist. Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. Products with different volume solids, different qualities also available on requests.
4. DFT variation can be obtained by change in application method / thinning ratio.
5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two component air drying aromatic polyurethane finish coating
It is recommended as topcoat for Original Equipment Machines, Hygienic, Maintenance painting where mild chemical resistance along with good abrasion resistance and decorative finish are required. Sometimes it is recommended as undercoat of finish coats application for economic benefits.
| COLOUR : | Assorted shades |
|---|---|
| FINISH : | Glossy / Semi glossy / Matt SOLIDS BY |
| VOLUME : | 40 ± 3% (Depends on shade) THEORETICAL |
| SPREADING RATE : | 13.33 sq.mt / lit at recommended DFT of 30 µ |
| FLASH POINT : | Base : Above 23°C Hardener : Above 30°C |
| DRYING CHARACTERISTICS : SURFACE DRY :20 - 30 minutes (At 30°C and 65% Relative humidity) | HARD DRY : Overnight FULL CURE : 7 days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
This being a Topcoat, which is applied over underneath primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 followed by solvent wipe for better bonding.
| MIXING RATIO : | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Conventional spray / By Airless Spray |
| THINNER : | Type 290 |
| POT LIFE : | 3 hours min at 30° C |
| RECOMMENDED DFT : | 30-40 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX :24 hours |
| COMPATIBILITY : | Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10minutes to initiate the reaction. Strain the paint through Nylon filter cloth 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :-By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensure the uniformity. Use quality brushes for paint application
| Thinner : | Type 290 |
|---|---|
| Addition : | 5 - 15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, Do not apply during rain, fog, or mist. Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. Volume Solids will vary depending on shades. Products with different volume solids are also available on request.
4 DFT variation can be obtained by change in application method / thinning ratio.
5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating.
This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application.
| COLOUR : | Industrial Shades |
|---|---|
| FINISH : | Glossy / Semi-glossy |
| SOLIDS BY VOLUME : | 40 ± 3% (Depends on shade) |
| THEORETICAL SPREADING RATE : | 13.33 sq.mt / ltr @ recommended DFT of 30 µ |
| FLASH POINT : | Base : Above 23°C Hardener : Above 23°C |
| DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : | SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
| MIXING RATIO : | Base: Hardener - As per our recommendations |
|---|---|
| APPLICATION : | By Brush / By Conventional Spray / By Airless Spray |
| THINNER : | Type 290 |
| POT LIFE : | 4 hours min at 30°C |
| RECOMMENDED DFT : | 30- 40 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth of 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :-By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application.
| Thinner : | 290 |
|---|---|
| Addition : | 5 - 15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i |
| Thinner : | 290 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28 - 0.37 mm |
| Nozzle Pressure : | : 1400-1800 p.s.i |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. Products with different volume solids and for special applications like Flexible coating and anti fungal/anti bacterial versions are available on requests.
4. DFT variation can be obtained by change in application method / thinning ratio.
5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two-component Air Drying acrylic aliphatic polyurethane finish coating.
This product has excellent gloss, moderate colour retention and non-yellowing properties, against Ultraviolet rays and weathering, This product is recommended as topcoat with suitable primers and undercoats for use in moderate Chemical & Saline atmosphere for better aesthetics and corrosion resistance. It is recommended for Transportation Industries, Infrastructure Projects, locomotives, steel structure etc. is recommended as a self-priming coat for direct adhesion on variety of substrate like MS, Aluminum, Galvanized Iron and selected plastic surfaces.
| COLOUR : | Assorted shades. |
|---|---|
| FINISH : | Glossy / Semi-glossy / Matt SOLIDS BY |
| VOLUME : | 40 ± 3% (Depends on shade) |
| THEORETICAL SPREADING RATE : | 15 sq.mt / ltr @ recommended DFT of 30 µ |
| FLASH POINT : | Base: Above 23° C Hardener: Above 23° C |
| DRYING CHARACTERISTICS (At 30°C & 65% Relative Humidity) : | SURFACE DRY : 70 - 80 minutes HARD DRY : Overnight. FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
This being a topcoat, which is applied over , primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
| MIXING RATIO : | Base: Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Conventional Spray / By Airless Spray |
| THINNER : | Type 290 |
| POT LIFE : | 4 hours min at 30°C |
| RECOMMENDED DFT : | 30-40 µ. |
| OVER COATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10minutes to initiate the reaction. Strain the paint through Nylon filter cloth 400 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :-By Conventional Spray / By Airless Spray
| Thinner : | 290 |
|---|---|
| Addition : | 5 - 15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | 290 |
|---|---|
| Addition : | Max 5% if required |
| Nozzle Orifice : | 0.28 - 0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i. |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog, or mist. Surface temperature must always be minimum of 3°C above Dew point.
2. Spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. Specific shades free from toxic pigment like Lead, Chrome, cadmium version is also available on request.
4. DFT variation can be obtained by change in application method / thinning ratio.
5. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two component, air-drying, Epoxy polyamide cured finish paint.
It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc.
| COLOUR : | Assorted Shades |
|---|---|
| FINISH : | Semi glossy |
| SOLIDS BY VOLUME : | 40 ± 3% (Depends on shade) |
| THEORETICAL SPREADING RATE : | 13.33 sq.mt / ltr at recommended DFT of 30 µ |
| FLASH POINT : | Base: Above 23° C Hardener: Above 23° C |
| DRYING CHARACTERISTICS : | SURFACE DRY : 90 minutes max HARD DRY : Overnight FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
| MIXING RATIO : | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Conventional Spray / By Airless Spray |
| THINNER : | 190 |
| POT LIFE : | 4-6hrs min at 30 ° C |
| RECOMMENDED DFT : | 30-40 µ |
| OVER COATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be over coated with PU, Chlorinated rubber and synthetic enamel paints. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Thinner Type 190 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Strain the paint through Nylon filter cloth depending on type of finish selection and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application: By Brush / By Conventional Spray / By Airless Spray Generally for brush application no thinner is required, however under adverse environmental condition about 5% by volume thinner 002 can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application
| Thinner : | 190 |
|---|---|
| Addition : | 5 - 15% |
| Nozzle Orifice : | 1.2 -1.4 mm |
| Nozzle Pressure : | 40-70 p.s.i. |
| Thinner : | 190 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28 0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%, or during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.3. DFT variation can be obtained by change in application method.4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.5. Products with amine curing agent are also available on request.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
Description
Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance.
It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc.
| COLOUR : | Selected industrial shades |
|---|---|
| FINISH : | Semi glossy |
| SOLIDS BY VOLUME : | 80 ± 2% |
| THEORETICAL SPREADING RATE : | 10 sq.mt. / ltr. at a recommended DFT of 80 µ |
| FLASH POINT : | Base : Above 25°C Hardener : Above 25°C |
| DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30°C) : | SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
| MIXING RATIO Base : Hardener ( As per our recommendations) : | Base : Hardener (As per our recommendation) |
|---|---|
| APPLICATION : | By Brush / By Airless Spray |
| POT LIFE : | 2 - 3 hours min at 30° C |
| RECOMMENDED DFT : | 75-100 mic. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be over coated with Epoxy, PU |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add EpoxyThinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application: By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniformity. Use quality brushes for paint application.
| Thinner : | Epoxy Thinner 190 |
|---|---|
| Addition : | Max 10 - 15% |
| Nozzle Orifice : | 2-3 mm |
| Nozzle Pressure : | 40-70 psi. |
| Thinner : | Epoxy Thinner 190 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.48-0.53 mm |
| Nozzle Pressure : | : 2700-3200.P.s.i |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.3. Products with different volume solids, MIO pigmented also with Amine Hardener are available on requests4. DFT variation can be obtained by change in application method / thinning ratio.5. Shelf life indicated is minimum for this Product in sealed condition and it is subjected to re-inspection thereafter. Individual component is required to store in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
